Humanoids · Cobots · AMRs · Warehouse automation

Robotics & Automation Production

Enclosures, covers, sub-assemblies, and end-of-arm tooling for large robotics programs, delivered finished and ready to install. We support you from the first EVT build through production runs of up to 5,000 pieces, without waiting on injection mold tooling.

  • ISO 9001:2015 (ANAB)
  • EVT · DVT · PVT builds
  • Inserts & assembly
  • DyeMansion finishing
  • Prototype to production

Robotics 3D printing at SNL Creative

SNL Creative is an ISO 9001:2015 certified contract manufacturer in Cypress, California that produces 3D printed parts for robotics and automation companies. We make end-of-arm tooling (EOAT), vacuum and soft grippers, sensor and camera mounts, humanoid robot covers, AMR and AGV body panels, cable management, and actuator housings. We work in SLS and MJF PA12, TPU 1301, Markforged continuous carbon fiber, FDM, PolyJet, and SLA, and support EVT, DVT, and PVT builds through bridge production.

Applications

Robot parts we produce

Hardware that moves, flexes, and takes impacts on the floor, in production quantities.

End effectors

End-of-arm tooling (EOAT)

Lightweight gripper bodies, vacuum manifolds with internal air channels, tool changers, and part-specific nests. Less EOAT mass means more payload and faster cycle times.

Grasping

Soft fingers & compliant grippers

TPU 1301 and lattice structures for compliant fingers, suction cup adapters, and pads that conform to fragile or irregular parts.

Humanoids

Covers, shells & skins

Head shells, faceplates, limb covers, and torso panels with cosmetic DyeMansion finishes. Soft-touch TPU zones where people make contact.

Mobile robots

AMR / AGV panels & bumpers

Body panels, sensor windows, LiDAR and camera bezels, and energy-absorbing TPU bumpers for warehouse and logistics robots.

Drive & joints

Actuator & electronics housings

Motor and gearbox housings, encoder covers, harness pass-throughs, and cable carriers (dress packs) for articulated joints.

Composite tooling

Composite layup tooling & fixtures

3D printed layup molds and mandrels for carbon fiber robot arms, links, and covers, with large-format tooling up to 36 × 24 × 36 in on the Stratasys Fortus 900mc. Also pick-and-place nests and calibration fixtures. See production tooling.

Materials & processes

Materials for parts that move

Robotics parts usually need a combination of stiffness, impact resistance, fatigue life, and a production-quality finish. Here's how we match them.

MaterialProcessWhere it fits
PA12SLS (EOS P396) & MJF (HP 5200 / 4200)The workhorse for robot housings, covers, EOAT bodies, and brackets. Tough, isotropic, and repeatable across production lots.
TPU 1301SLSElastomer for soft fingers, bumpers, grommets, and protective skins. Supports lattice structures with tunable stiffness.
Onyx™ + continuous carbon fiberCFF (Markforged)Stiff, metal-replacement gripper bodies, tool plates, and fixtures where deflection matters.
Nylon 12, ASA & PCFDM (Stratasys Fortus 450mc & 900mc)Large fixtures, guards, and brackets in tough engineering thermoplastics.
Vero™ + Agilus30™PolyJet (Stratasys J750)Multi-material prototypes that combine rigid and rubber-like regions in one print, such as overmold-style fingers and animatronic components.
Engineering resinsSLA (Stratasys Neo 450)High-detail sensor mounts, optical alignment parts, and cosmetic master models.

We'll recommend process and material from your load case, duty cycle, and finish requirements at quote.

Post-processing & assembly

Finished components, not raw prints

Robotics teams don't have time to send printed parts out for smoothing, color, inserts, and assembly. We do all of it in-house and ship parts that go straight into the robot.

Vapor smoothing

DyeMansion Powerfuse S vapor smoothing seals and smooths SLS and MJF parts, giving a cleanable, injection-mold-like surface that resists staining and moisture.

Color & dyeing

DyeMansion DeepDye for consistent, through-surface color on PA12 and TPU, from production black to brand colors.

Painting & cosmetic finishing

Sanding, priming, painting, and texture for appearance parts, demo units, and customer-facing hardware.

Threaded inserts & hardware

Heat-set threaded inserts, fasteners, and hardware installed in-house so parts bolt straight into your build.

Sub-assembly & kitting

Multi-part sub-assemblies built, checked, labeled, and kitted to your BOM, ready for your line.

Inspection

Dimensional checks and 3D scan deviation reports against CAD before anything ships.

Program workflow

Built for the hardware development cycle

Robotics programs move fast. We hold the same process from your first engineering build to pilot production, so parts behave the same at every gate.

  1. 1 · DFAM reviewWe review your CAD for wall thickness, inserts, snap fits, and channels before anything prints.
  2. 2 · EVTFast-turn functional prototypes for fit, motion, and first testing.
  3. 3 · DVTLocked materials and processes for durability, drop, and environmental testing.
  4. 4 · PVT & pilotRepeatable lots with finishing, threaded inserts, and kitting or sub-assembly.
  5. 5 · Bridge productionProduction runs up to 5,000 pieces without mold tooling, plus spares for fielded fleets.
Quality & compliance

Production consistency, documented

  • ISO 9001:2015 certified quality management system, ANAB-accredited (Certificate No. 1119400).
  • Controlled build parameters and material lot tracking, so DVT parts and production parts match.
  • Dimensional inspection with in-house 3D scanning for deviation reports against CAD.
  • Production finishing, including DyeMansion vapor smoothing for sealed, cleanable surfaces and DeepDye coloring. See finishing services.
  • Post-processing & assembly: heat-set threaded inserts, kitting, and sub-assembly ready for your line.
  • Confidentiality: NDAs are standard. Unreleased robot designs stay inside our facility.
Why SNL Creative

Robotics is one of our top verticals

  • Operating since 2008 in Cypress, CA, building prototypes and production parts for engineering teams across Southern California and nationwide.
  • Enclosures and sub-assemblies for large robotics programs, not just one-off prototypes. Production 3D printing on SLS and MJF for repeatable, tool-free manufacturing.
  • Soft and rigid in one shop: TPU 1301 lattice expertise, as a member of the EOS Digital Foam network, alongside stiff carbon fiber composites.
  • Hardware integration experience. Leadership ran the additive lab at an EV OEM, supporting subsystem builds and mechanical and electrical integration.
  • Animatronics heritage. Our work on multi-material animatronic eyes and entertainment robotics carries over directly to humanoid faces and covers.
FAQ

Robotics & automation 3D printing FAQ

What is the best 3D printing material for end-of-arm tooling?

For most EOAT, SLS or MJF PA12 is the best balance of low weight, toughness, and the ability to print internal vacuum channels. When stiffness is critical, such as long fingers or tool plates, Markforged Onyx with continuous carbon fiber is often the better choice. TPU 1301 is used for compliant contact surfaces.

Can 3D printed parts be used in production robots?

Yes. Many robotics companies ship SLS and MJF PA12 covers, housings, brackets, and EOAT in fielded robots, especially at volumes from tens up to a few thousand units, where injection mold tooling doesn't pay off yet. We hold a controlled process so production parts match what you validated in DVT.

Do you make humanoid robot covers and shells?

Yes. We produce head shells, faceplates, and limb and torso covers in PA12 with DyeMansion vapor smoothing and dyeing for a production-grade cosmetic finish. TPU 1301 can be added for soft-contact areas. Large or complex shells can also be reverse engineered from scans or sculpts with our CAD and digital sculpting team.

Do you support EVT, DVT and PVT builds?

Yes. We support each hardware gate with fast-turn EVT prototypes, locked-process DVT builds for testing, and PVT and pilot lots with finishing, inserts, and kitting. Staying with one supplier through all three gates avoids part-to-part variation when you change vendors.

Can you 3D print composite layup tooling for robot parts?

Yes. We print layup molds and mandrels, typically in ULTEM 1010 or ULTEM 9085, for carbon fiber robot arms, links, and covers. Printed composite tooling is lighter and faster to produce than machined aluminum, which suits robotics teams iterating on composite structures.

Can you install threaded inserts and assemble parts?

Yes. We install heat-set threaded inserts and handle post-processing, kitting, and sub-assembly, so parts arrive ready for your line.

How do I get a quote for robotics parts?

Upload STEP or STL files to our instant quote tool for pricing. For multi-part builds, assemblies, or programs with EVT/DVT/PVT schedules, email orders@snlcreative.com with your BOM and target quantities.

Building robots? Let's build the parts.

Upload CAD for instant pricing. For full EVT/DVT/PVT builds, assemblies, or production forecasts, email orders@snlcreative.com with your BOM and quantities.

Get an Instant Quoteorders@snlcreative.com714-420-8957

Related capabilities