Aerospace & Defense Additive Manufacturing
ISO 9001:2015 certified, ITAR-registered contract manufacturing for flight-test hardware, ECS ducting, assembly tooling, and low-rate production parts. We build to your drawing, your material callout, and your documentation flowdown, from first article through bridge production.
- ISO 9001:2015 (ANAB)
- ITAR registered
- AS9102-format FAI on request
- Material certs & CoC
- Lot traceability
Aerospace additive manufacturing at SNL Creative
SNL Creative is an ISO 9001:2015 certified, ITAR-registered additive and contract manufacturer in Cypress, California. Aerospace, defense, space, and UAS programs use us for flight-test brackets, environmental control system (ECS) ducting, cable management hardware, drill and bond fixtures, and low-rate production parts. We print in FDM high-performance thermoplastics, SLS and MJF PA12, continuous carbon fiber composites, and SLA. Each build ships with first article inspection, material certifications, and lot traceability when your purchase order requires them.
What we build for aerospace & defense programs
Parts that see real loads, real heat, and real audits, not just display models.
Flight-test brackets & clips
Brackets, clips, and mounts for flight-test instrumentation and interior components. Built to your drawing and qualified on your program's material and process allowables.
ECS & cabin air ducting
Duct runs, shrouds, plenums, and diffusers printed in ULTEM 9085 and ULTEM 1010 for their thermal performance. Consolidated into single parts with no bonded joints and internal geometry that can't be machined.
Cable management & avionics hardware
P-clip alternatives, standoffs, harness routing guides, connector backshell prototypes, and wire harness formboard tooling.
Composite layup tooling & fixtures
3D printed layup molds, mandrels, and trim and drill fixtures for carbon fiber composite components, printed in ULTEM 1010 and ULTEM 9085, including large-format tools up to 36 × 24 × 36 in on the Stratasys Fortus 900mc. Lighter and faster to make than machined aluminum. See production tooling.
UAS airframes & payload housings
Payload and electronics enclosures, sensor pods, and airframe components for unmanned systems, from EVT iterations to repeatable low-rate production.
GSE, covers & test articles
Ground support equipment components, protective covers, handling fixtures, and wind-tunnel and form/fit/function models.
Aerospace-grade materials, matched to the job
We recommend the process and material from your load case, temperature, flammability, and documentation requirements, not from whichever machine is open.
| Material | Process | Where it fits |
|---|---|---|
| ULTEM™ 9085 | FDM (Stratasys Fortus 450mc & 900mc) | FST-compliant (flame, smoke, toxicity) PEI widely used for aircraft interior parts, ducting, and enclosures. High strength-to-weight. |
| ULTEM™ 1010 | FDM (Stratasys Fortus 450mc & 900mc) | Highest heat resistance of the FDM family. Our primary material for composite layup molds, mandrels, and bond tooling, plus hot-zone ducts and brackets. |
| Antero™ PEKK | FDM (Stratasys Fortus 450mc & 900mc) | PEKK-based, with excellent chemical resistance and low outgassing. A candidate for space and fluid-exposure applications. |
| Nylon 12 | FDM (Stratasys Fortus 450mc & 900mc) | Tough, fatigue-resistant nylon for fixtures, clips, and snap-fit tooling. |
| PA12 | SLS (EOS P396) & MJF (HP 5200 / 4200) | Lightweight brackets, ducting, and housings with complex internal channels. Self-supporting powder bed, so there are no support scars on critical surfaces. |
| Onyx™ + continuous carbon fiber | CFF (Markforged) | Aluminum-replacement fixtures, jaws, and tooling plates with continuous fiber reinforcement where you need stiffness. |
| Engineering resins | SLA (Stratasys Neo 450) | High-accuracy wind-tunnel models, master patterns, and smooth-surface form/fit articles. |
Material data sheets are provided at quote. Flight qualification of any material or process remains with the customer's program and engineering authority.
Delivered as a finished part, not a raw print
Customers work with us because we hand back a finished, documented component, not a part that still needs a second vendor for finishing, inserts, and assembly.
Vapor smoothing
DyeMansion Powerfuse S vapor smoothing seals and smooths SLS and MJF parts, giving a cleanable, injection-mold-like surface that resists staining and moisture.
Color & dyeing
DyeMansion DeepDye for consistent, through-surface color on PA12 and TPU, from production black to brand colors.
Painting & cosmetic finishing
Sanding, priming, painting, and texture for appearance parts, demo units, and customer-facing hardware.
Threaded inserts & hardware
Heat-set threaded inserts, fasteners, and hardware installed in-house so parts bolt straight into your build.
Sub-assembly & kitting
Multi-part sub-assemblies built, checked, labeled, and kitted to your BOM, ready for your line.
Inspection
Dimensional checks and 3D scan deviation reports against CAD before anything ships.
From first article to low-rate production
One supplier from the first iteration to the frozen-process production lot, so you don't re-qualify a new vendor at every gate.
- 1 · RFQ & DFAM reviewEngineers review CAD, drawings, and specs for printability, orientation, and tolerance stack-up.
- 2 · Prototype & EVTQuick-turn iterations so design teams can test fit, function, and load paths.
- 3 · First articleFAI against the drawing, with dimensional inspection and material certs.
- 4 · Frozen processLocked machine, material lot, orientation, and parameters for qualification and repeat builds.
- 5 · LRIP & sustainmentLow-rate and bridge production, plus spares and obsolete part recovery through 3D scanning.
Documentation built for aerospace audits
- ISO 9001:2015 certified quality management system, ANAB-accredited (Certificate No. 1119400).
- ITAR registered. Controlled technical data is handled under export-control procedures, with access limited to authorized U.S. persons.
- First article inspection reports in AS9102 format on request, plus certificates of conformance and material certifications.
- Lot & build traceability from powder or filament lot to machine, build ID, and operator.
- Dimensional verification with in-house 3D scanning for part-to-CAD deviation reports.
- Flowdown-friendly. We routinely support suppliers to AS9100-certified primes with the documentation their POs require.
Engineers who have run production AM programs
- Operating since 2008 in Cypress, CA, building prototypes and production parts for engineering teams across Southern California and nationwide.
- Six print technologies under one roof: SLA, SLS, FDM, Color PolyJet, MJF, and continuous carbon fiber, so the process fits the part.
- In-house finishing with DyeMansion vapor smoothing and dyeing, plus inserts and production finishing.
- Close to the LA aerospace corridor. We support teams in El Segundo, Hawthorne, and Long Beach, with local pickup and delivery.
- Production mindset. Leadership built and ran the additive manufacturing lab at an EV OEM, supporting vehicle programs from prototype through integration.
Aerospace & defense additive manufacturing FAQ
Is SNL Creative ITAR registered?
Yes. SNL Creative is ITAR registered. Controlled drawings, models, and technical data are handled under our export-control procedures, with access restricted to authorized U.S. persons. Tell us at RFQ if your data is ITAR- or EAR-controlled so we can route it correctly.
Are you AS9100 certified?
SNL Creative holds ISO 9001:2015 certification (ANAB-accredited). We are not AS9100 certified, but we regularly supply AS9100-certified primes and their suppliers. We provide the flowdown documentation they require, including first article inspection in AS9102 format, certificates of conformance, and material certifications.
Can you print flight-ready brackets?
We print brackets, clips, and ducting in aerospace thermoplastics such as ULTEM 9085 to your drawing and process requirements. Whether a part is flight-ready depends on your program's qualification of that material, process, and design. We support that with a frozen, documented process and full traceability on every lot.
Which 3D printing material is used for aircraft interiors?
ULTEM 9085 is the most widely used FDM material for aircraft interior and ducting applications because it is FST compliant (flame, smoke, and toxicity) and has a high strength-to-weight ratio. For lightweight non-interior brackets and complex internal channels, SLS or MJF PA12 is often the better fit.
Can 3D printing replace machined aluminum tooling?
For many composite layup molds and mandrels, drill blocks, trim guides, bond fixtures, and check gauges, yes. Continuous carbon fiber (Markforged) and ULTEM 1010 tooling is lighter, cheaper, and faster to make than machined aluminum. It also skips the long queue for machined tooling. We review each tool's loads and temperatures before recommending a material.
What are your lead times for aerospace parts?
Lead time depends on project scope, part size, quantity, process, and finishing and documentation requirements. The more information you share up front (drawings, specs, quantities, and need dates), the more accurate our lead time will be. Qualification and production lots are scheduled to your program milestones. Upload CAD to our instant quote tool for pricing, or email orders@snlcreative.com for controlled-data RFQs.
Send us your aerospace or defense RFQ
Upload CAD for an instant quote. For ITAR-controlled data, drawings with GD&T, or programs that need FAI and certs, email orders@snlcreative.com and an engineer will respond directly.
Get an Instant Quoteorders@snlcreative.com714-420-8957